Personal Tracker

Personal Tracker User Manual

TS-MV6

1. Technical Parameters

1.1 Working Voltage：3.8V DC

1.2 Battery Capacity：5200 mA (Samsung battery)

1.3 GSM Band：850/900/1800/1900MHz

1.4 GPRS:Class12,TCP/IP

1.5 GSM Antenna 50Ωlinear polarization passive PiFA antenna

1.6 GPS Frequency：1575MHz 20Channels

1.7 GPS Tracking Sensitivity：-159dBm

1.8 GPS Capturing Sensitivity：-144dBm

1.9 GPS Locating time：cold start≈28s（Open sky）

Hot start≈2s（Open sky）

1.10 GPS precision：10m（2D RM）

1.11 GPS Antenna：50Ωcircular polarization 360°active ceramic antenna

1.12 Working Temperature：-20℃～+70℃

1.13 Working Humidity：20%～80%RH

2：Characteristics

2.1.Inbuilt GPS Module

2.2.Internet positioning service center, used to receive and send positioning information

2.3. GSM/GPRS modem supports Quad frequency bands, .850/900/1800/1900 MHz

2.4.High-sensitivity, new workmanship and the most advanced GPS chip

25. Can work effectively in limited space such as urban canyon

2.6.Fast signal acquisition

2.7. Supports single positioning and continuous tracking;

2.8.Supports the location information inquiry by SMS and Internet

2.9.May monitor without disturbing the tracked person and realize real-time tracking;

2.10.Can position the holder by call or SMS

2.11. 5200MA battery , can use 5 days, 10400 MA battery can use 10 days

2.12. can charging the battery to the mobilephone,same as a mobile battery.

3：Appearance Diagram

3.1 Appearance(different color)

3.2;Rechargeable

3.3 The internal structure (5200MAH)

3.4 The internal structure (10400MAH)

3.4 charge for the mobile phone

4. Status Indicator

4.1 Green LED（GSM status indicator）

When GSM signal is normal，the green LED glistens (0.3S/2S). When uploading GPRS data，the LED glistens quickly. The LED glistens slowly when in no signal (2S/5S)。

4.2 Blue LED（GPS status indicator）

When GPS signal is normal，the blue LED glistens. When GPS just starts but still not locates, the LED is in constant glow. The LED is off when GPS closed.

6. User Settings

1) Administrator number set
Text command	Parameter	Sample
Admin Add	710#number# 711#number#	710#13500135000# 711#13800138000#
Admin Del	D01# D02#	D01# D02#
Command Description	1) admin number can control the oil and power and resume factory settings 2) Only two numbers can be admin number. 3) Change admin number must resend the command.
Command Feedback	Successful Setting：Add admin account 1 OK!

2) View administrator number
Text command	Parameter	Sample
View	901#	901#
Command Description	This directive is used to view Device Manager number.
Command Feedback	Successful Setting：Admin1: Admin2:

3)Authorized number set
Text command	Parameter	Sample
Authorized Add	101# number # 102# number # 103# number #	1：101#13800138000# 2：102#12345678912# 3：103#12345678912#
Authorized Del	D11# D12# D13#	D11# D12# D13#
Command Description	1) Authorization number for SMS control oil. 2) only three numbers to set the authorization number 3) change the authorization number needs to delete the previous number
Command Feedback	Successful Setting：Add Authorization account 1 OK!

4) View authorized number
Text command	Parameter	Sample
View authorized	C10#	C10#
Command Description	This directive is used to view the equipment authorization number
Command Feedback	Successful Setting： Authorization 1： Authorization 2： Authorization 3：

5)APN
Text command	Parameter	Sample
APN Setting	802#username#password	1：802#intenet#123#123#
Command Description	APN differs according to the local telecom operators. For example：APN request password，please refer to Sample1，and Sample2 for no password.
Command Feedback	Successful Setting：SET APN OK！

6)SERVER
Text command	Parameter	Sample
SERVER Parameter	803#SERVER # port#	803#222.217.240.243#8011#
Command Description	Change the IP and port when move to a new server port：10~65535 1 is domain and 0 is IP；
Command Feedback	Successful Setting：set IP OK!

7) View SERVER
Text command	Parameter	Sample
CIP Parameter	CIP#	CIP#
Command Description	This directive is used to set the IP address and server platform port
Command Feedback	IP：222.217.240.243 PORT：8011#

8)VIBRATION
Text command	Parameter	Sample
VIBRATION Parameter	761#2#,alarming way#	1)761#2#3#
Close VIBRATION	765#	765#
Command Description	the sensitivity value of the vibration is from 1 to 5，1is the most sensitive and o is close. Alarming ways: 1, calling 2, texting, 3 calling and texting. Must set the center number and receiving number.
Command Feedback	set vibration alarm level，OK!

9) FACTORY
Text command	Parameter	Sample
FACTORY Parameter	940#	1)940#
Command Description	Restore the factory setting Only center number can initial this function Factory setting will recover to the original setting
Command Feedback	Successful Setting：FACTORY OK！

10) Upload frequency
Text command	Parameter	Sample
TIMEER Parameter setting	730#uploading interval#	730#30#
Command Description	Time scope： 30~180seconds； 30~180,means time interval；the default value is 60seconds！
Command Feedback	Successful Setting：Set upload time, ok!

11) Low power alarm switch settings
Text command	Parameter	Sample
STATIC	750#shapl#	750#1# 750#0#
Command Description	This command is used to open or close the Low battery alert administrators when the function is enabled by default state.
Command Feedback	Successful Setting：Set low power Switch ok!

12) Electronic fence set
Text command	Parameter	Sample
STATIC	FNECE#Latitude #Longitude #Radius#	FENCE#22.530530#114.02223 #5#
Command Description	This command is used to open or close the Low battery alert administrators when the function is enabled by default state.
Command Feedback	Successful Setting：Version information IMEI

13)STATIC
Text command	Parameter	Sample
STATIC	731#time interval#	731#5#
Command Description	Time scope：1~60 minutes；The device has3D transmission and the default time interval are 5 minutes.
Command Feedback	Successful Setting：Set static upload time ok!

14) Close Upload
Text command	Parameter	Sample
command	732#	732#
Command Description	Close Upload
Command Feedback	Successful Setting：Close upload GPRS information ok!
Resume upload	MUP# uploading interval#

15)WHERE
Text command	Parameter	Sample
WHERE	988#	988#
Command Description	Check the longitude and altitude and other information of the device
Command Feedback	Reply with longitude and altitude, speed and IMEL.

16)URL
Text command	Parameter	Sample
WHERE	666#	666#
Command Description	Check the location link of Google map
Command Feedback	<Datetime:12-07-05 13:21:30> http://maps.google.com/maps?q=N22.540885,E113.95265

17)GMT
Text command	Parameter	Sample
GMT	801# location time #	801#E8#
Command Description	The default time zone is Beijing time. If time zone need revised, please operate according to the above command.
Command Feedback	Successful Setting：Set time zone ok!

18)RESET
Text command	Parameter	Sample
RESET	930#	930#
Command Description	Reset the device
Command Feedback	Successful Setting：Reset system, ok!

19)LANG
Text command	Parameter	Sample
LANG Parameter	920#1#	1) 920#1# Chinese 2) 920#2# English
Command Description	；When check the location, it will reply the Chinese location in Chinese language setting; while reply the URL link when in English language setting.
Command Feedback	Successful Setting：SET LANG OK！

7. Check the Location by Texting

7.1 Check the longitude and latitude by texting.

Admin number or family mobile phone number can text to the device number and the device will open he GPS and uploading the longitude and latitude, time, speed and direction data. If the locating fails because of environment, the device will send the last GPS location information.

7.2Call the device number to check the longitude and latitude

Admin number or family mobile phone number can call the device number and hang up after connecting and the device will open he GPS and uploading the longitude and latitude, time, speed and direction data. If the locating fails because of environment, the device will send the last GPS location information.

7.3 Check the location by texting.

Admin number or family mobile phone number can text to the device’s number and the device will text back the current location information.

9．SOS

9.1 Users press SOS key for over 3 seconds and SOS LED will glisten quickly（0.3S/0.3S）. The device will open the GPS and uploading the location data every 15 seconds until the SOS alarm is closed. You can close the SOS alarm by texting or online platform.

9.2 Meantime, the device will call SOS mobile phone number、admin number, family mobile phone number until there is person answering it(the call will be recorded and saved on the platform).

9.3 The monitoring center will open a popup window of alarm. The monitoring center can close the popup window after dealing with the alarm. The system will send a command to remove the alarm and the device will close the SOS alarm after receiving the command.

10. Trouble shooting

The device is not online or offline on the web platform.

10.1 First, please check the three LED working state. If possible, you can call the device’s number to check.

10.2 if not connected，the device maybe out of signal. Please check the SIM card working state or go to the open sky to check.

10.3 If reminding the device SIM card is out of deposit, please make deposit by the telecom operator.

10.4 If connected and the device’s SIM card with enough deposit, please check with the operator that the status of the SIM card’s GPRS function.

10.5 The device power off when calling it.

10.6 Please the offline area（individual offline or group offline）in order to check the network of the operator.

10.7 When the receiving of GSM signal is abnormal, please check the SIM card installation; or the location is out of GSM signal (like in basement).

10.8 The green GSM LED does not glow after inserting the SIM card; please check the power of the device by charging it.